C2000 SERIES XDS510LC JTAG EMULATOR DRIVER

All dimensions are in inches and are nominal dimensions, unless otherwise specified. This Jtag is working fine with our boards. Operation of this equipment in other environments may cause interference with radio communications, in which case the user at his own expense will be required to take whatever measures may be required to correct this interference. TCK is provided as an optional target system test clock source. Now connect the tail of the emulator to the 2 x 7 header on your target board. Your system configuration should now look like that in Figure or Figure After a few moments windows will detect new hardware and prompt you with New Hardware Found screens. After powering up, the program goes nowhere, and the board don’t respond as expected.

Please be aware that the products described herein are not intended for use in life-support appliances, devices, or systems. In this application the TCK signal is left unconnected. Web searches have revealed tiny tidbits here and there, but not much. Start display at page:. Then I connect to the board through JTAG link, and reset the cpu, then just run the cpu don’t load any program because the program have been programmed into flash , everything is ok. Technical Reference Printed in U. July Copyright Altera More information. Is there anyway to load my programmes into RAM

After programming Flash, It is not executing program after a power on reset. I’m worried that I may end up having to try to build a program to do this. Apply power to the target board Remove the bottom cover from the unit by removing four screws. This emulator used to work fine with our old TMSF design. We are using CAN for our system. This adapter resolves the voltage differences required for correct operation. Whats the compiler used for Jjtag It seems the flash boot mode is selected correctly.

  DIE WELLE FILM HAUPTPERSONEN

This means that, the DSPs are already locked. According to me i feel all According to me i feel all initializations are done properly. User Manual Copyright Apricorn, Inc.

This guide is designed to acquaint you with the features and functionality of the Power off the unit. Signal buffering in noisy target environments Emulator header metal wear protection This adapter plugs onto the emulator s 2×7 female connector on one side and the target s 2×7 male connector on the other.

This is an example of a caution statement. The emulation signals in this example are buffered to isolate the processors from the emulator and provide adequate signal drive for the target system. To support operation with the lower voltage devices Spectrum Digital has designed the Low Voltage Adapter, part This adapter drivrr onto the emulator s 2×7 female connector on one side and the target s 2 x 7 male connector on the other.

The idea that devices can simply. I have designed a little evaluation-board Please be aware that the products described herein are not intended for use in life-support appliances, devices, or systems. The overall cable length is approximately 6 feet, 10 inches.

C2000 Series XDS510LC JTAG Emulator Technical Reference

Spectrum Digital does not test or guarantee these timings. Laser Wireless Rechargeable Mouse Model: In each case, the worst case path delay is calculated to determine the maximum system test clock frequency.

  WEST END WATCH CO. L SOWAR 1916

But without knowing the password, it can never be unlocked, using JTAG emulator. By default, the F is protected by CSM.

Test clock input to the emulator. All rights reserved worldwide. If any body have any idea pl. So it is not working as a standalone system.

The emulator provides only a single MHz test clock.

C XDSLC USB EMULATOR from Spectrum Digital, Inc.

Then I connect to the board through JTAG link, and reset the cpu, then just run the cpu don’t load any program because the program have been programmed into flasheverything is ok. M Welcome Thank you for purchasing one of the most feature-rich keyboard, video, and mouse switches on the market. Spectrum Digital does not warrant nor is liable for the product described herein to be used in other than a laboratory development environment. But this is again working fine with our old TMSF boards.

No power to target” All the connections are proper and voltage at the pin PD Presence Detect of the emulator was The platform More information. Windows is a registered trademark of Microsoft Corporation. To make this website work, we log user data and share it with processors.

Author: admin